No current events.
|Stabilizing System Pressure|
|Written by USDOE Office of Industrial Technologies|
|Wednesday, 09 June 2010 12:53|
Stabilizing System Pressure
Stabilizing system pressure is an important way to lower energy costs and maintain reliable production and product quality. The need to stabilize system pressure should be guided by the compressed air demand patterns and the minimum acceptable pressure level required for reliable production. High-volume intermittent air demand events can cause air pressure to fluctuate, which is often misinterpreted as insufficient pressure. In some cases, improperly set compressor controls will cause another compressor to start, but because of the time required for the new compressor to ramp up, there will be a shortfall of air supply to the system. Such a delay can cause the system pressure to decay, resulting in lost production. Three methods can be used to stabilize system pressure: adequate primary and secondary storage, Pressure/Flow Controllers (P/FCs), and dedicated compressors.
Primary and Secondary Storage
One or more compressed air applications having large, intermittent air demands can cause severe, dynamic pressure fluctuations in the whole system, with some essential points of use experiencing inadequate pressure. Such demand is often of short duration; properly sized primary and secondary storage can supply the needs of the intermittent demand. The time interval between the demand events is adequate to restore the storage receiver pressure without adding compressor capacity. Primary storage receivers can:
• Prevent frequent loading and unloading of compressors
• Collect condensate, which may be carried over from the aftercooler and moisture separator
• Provide some radiant cooling to reduce moisture content and air dryer load if located in a cool location and installed upstream of the dryer
• Provide dampening of pressure pulsations from reciprocating compressors. Secondary storage receivers can be used to:
• Supplement the primary receivers to stabilize system pressure and thus keep unneeded compressors from starting
• Supply adequate compressed air for a single intermittent event of a known duration.
The secondary receiver should be located as close to the end use as is practicable and its pressure rating must be at least equal to that of the primary receiver(s).
Pressure fluctuations may also occur due to inadequate storage or because the system pressure is at or near the lowest level of the compressor pressure control band. If a large, intermittent demand event occurs when the pressure is at or near the lowest level in the control band, the pressure in the distribution piping falls even further, affecting critical end-use applications. In such a case, the installation of a relatively small receiver with a check valve upstream of the application causing the demand event may address the problem.
A Pressure/Flow Controller (P/FC) is a device that serves to separate the supply side of a compressed air system from that system’s demand side. P/FCs use the principle of operating compressors to fill and store air in receivers at higher pressures. P/FCs then reduce the pressure and supply it to the system at the pressure required by that system’s compressed air applications. P/FCs work with pilot-operated regulators or electronic controls to sense and monitor the system’s pressure downstream of the valves. Controlled pressure and adequate upstream storage are critical to satisfactory performance. P/FCs normally respond rapidly to demand fluctuations and maintain system pressure within a narrow band. For peak demand events, sufficient storage is necessary to release the stored air quickly into the system to maintain required downstream pressures within an acceptable tolerance. With proper design and system controls, storage can be used to meet air demand and reduce compressor run time.
Applications some distance from the main compressor supply or those with pressure requirements that differ from the main system requirements may be served by a dedicated compressor. Small or unit type compressors (generally up to 10 hp maxi- mum) can be very suitable for an application whose pressure level is higher than that of the plant’s other applications. Generally, such compressors can be located close to a point of use, avoiding lengthy piping runs and pressure drops; are adaptable to a wide range of conditions such as temperature, altitude, and humidity; and do not require separate cooling systems.
FOR ADDITIONAL INFORMATION, PLEASE CONTACT:
EERE Information Center 1-877-EERE-INF (1-877-337-3463) www.eere.energy.gov
Industrial Technologies Program Energy Efficiency and Renewable Energy U.S. Department of Energy Washington, DC 20585-0121 www.eere.energy.gov/industry
|Recover Heat from Boiler Blowdown
01/07/2010 | USDOE Office of Industrial Technologies
Recover Heat from Boiler Blowdown Heat can be recovered from boiler blowdown by using a heat exchanger to preheat boiler makeup water. Any boiler with continuous blowdown exceeding 5% of the steam ra [ ... ]
|Determining the Right Air Quality for Your Compressed Air System|
09/06/2010 | USDOE Office of Industrial Technologies
Determining the Right Air Quality for Your Compressed Air System Knowing the proper air quality level required for successful production is an important factor in containing compressed air energy and [ ... ]